模载联合支援站

引用框:

V2.61的变化：
从地图“南方区域7.2.0”增加底盘“KamAZ neo”。
-重新制作刹车（稍微柔和一点，调整平衡、温度、速度、努力）。
-机舱和气动座椅（制动下）的小变化。
-校正轴上的负载。
-在V 2.6中的其他行为。

-改进了悬架、驾驶室、发动机、变速器、制动器、气动座椅、机舱内的摄像机。
-支持所有默认预告片，并且还添加：SCANIA RS [RJL]；SCANIA143M；IVCO 190～38专用；KamAZ 54-64-65；MAZ-532-422.
-在所有添加轨道修正的旋转轴上。
-一切都被测试了。
我测试的平均发动机为500～540升/秒，行驶速度为90-105kM/h，货运量为20-25吨。货物40吨80-95kg/h，货物60-65吨。70～85公里/小时。
高达110公里/小时，你将被分散，只有在山下或不断的气体在地板上。背上的货物感觉到了，上升甚至不大，有一个良好的滚动，爬山。
-方向盘的灵敏度，为你调整游戏的设置。
-对于那些不喜欢管理变革的人，在档案馆里
有一个标准控制的第二个文件。
（To.Trkkv2.2.1i标准控制从~
-文件被锁定，除了底盘，当添加和编辑底盘时，保存时，它会要求密码，只需点击“OK”。

测试版本1.31

複製內容到剪貼板

原始碼:

 

Changes in V2.6.1:

– Added chassis “KamAZ neo” from the map “Southern region 7.2.0”.

– Remade the brakes (made a little softer and adjusted the balance, temperature, speed, effort)

– Small changes in the behavior of the cabin and pneumatic seating (under the brakes).

– Corrected the load on the axis.

– Other behavior as in V 2.6.



– Improved physics of suspension, cab, engine, transmission, brakes, pneumatic seat, cameras in the cabin.

– Supports all default trailers, and also added: Scania RS [RJL]; Scania 143m; Iveco 190-38 Special; KamAZ 54-64-65; MAZ-5432-6422.

– On all added tracks corrected rotary axes.

– Everything is tested.

– I tested on average engines 500-540 l / s. Cruising speed along motorways 90-105 km / h with a cargo of 20-25 tons. With cargo 40 tons 80-95 km / h. The cargo is 60-65 tons. 70-85 km / h.

– Up to 110 km / h little where you will be dispersed, only under a hill or constantly gas in the floor. The cargo behind the back is felt, the rises are not even big, with a good roll on, and climbing the mountain.

– The sensitivity of the steering wheel, adjust the settings of the game for you.

– For those who are not fond of changes in management, in the archive

there is a second file with standard control

(Physics_of_the_truck_V2.6.1_standard_control_from_ ~ Tok ~).

– P.S. The files are locked, except for the chassis, when adding and editing the chassis, when saving, it will ask for the password, just click “ok”.



Test for version 1.31.x